Consumers - SBR-AC3200P: Installation on FiOS Service
FAQs

ARRIS Consumer Care

Article

SBR-AC3200P: Installation on FiOS Service

« Go Back

Information

 
Question
How do I install my SBR-AC3200P on a FiOS Service?
Answer
The SBR-AC3200P is a wireless router that provides secure high-speed Internet connectivity to a wired or wireless network devices in the home or small business network.  It is also compatible with Cable, DSL/U-verse, and FIOS service. 

FiOS service operates over a fiber-optic communication network.  Some FiOS setups will use an Ethernet cable for data and coaxial cable for video, while others may use the Multimedia over Coax Alliance (MoCA) protocol for both data and video over a single coaxial cable. 

This document contains the following sections:
CAUTION: To better secure your network, ARRIS recommends to change the default Admin user name & password and the default wireless password immediately after connecting to the Internet.

Requirements: 
  • Active FiOS Internet service
  • Ethernet cable Internet connection

    NOTE: Consult with the service provider to see if the SBR-AC3200P is suitable for usage.

Before the Installation

Verify that the following items were included with the ARRIS SBR-AC3200P wireless router.  The SBR-AC3200P, power supply and Ethernet cable are necessary to perform the installation. 

NOTE: The quick start guide and warranty card can be downloaded from www.arris.com/consumers. 

  • Wi-Fi Router
  • Power Cable
  • Wireless Installation Guide
  • Ethernet Cable
  • End User License Agreement
 Testing Internet Connection
  1. Without disconnecting the existing network, power on a computer. 
     
  2. Open a web browser on the computer (such as Internet Explorer, Google Chrome, Firefox. or Safari).
     
  3. Enter the address http://www.surfboard.com in the address bar and press the Enter key. 

    NOTE:  If the Internet is not accessible, please contact the service provider to setup Internet service.
 

Install the SBR-AC3200P on FiOS Service

  1. Disconnect the existing Ethernet cable with Internet connectivity and connect the blue Ethernet cable (included) to the Ethernet port of the ONT or Ethernet wall outlet.

    NOTE: The existing Ethernet cable with Internet connectivity can be used instead of the blue Ethernet cable to connect to the SBR-AC3200P.

     
  2. Connect the other end of the blue Ethernet cable to the blue WAN port on the rear of the SBR-AC3200P.
     
  3. Connect the power cord to the rear of the SBR-AC3200P and plug it to an available electrical wall outlet.  Allow 30 seconds for the Front Panel Primary LED to become solid green.

    NOTE 1:  If the Front Panel Primary LED is flashing green make sure both ends of the blue Ethernet cable is securely connected between SBR-AC3200P and ONT or try using another Ethernet cable. 

    NOTE 2: If the Front Panel Primary LED is flashing green, power cycle the SBR-AC3200P.  If the Front Panel Primary LED continues to flash contact the service provider to troubleshoot the Internet connection.

     
    LEDColor/BehaviorDescription
    Front Panel Primary LED 
    Connection status
    Solid greenWi-Fi router is connected to the
    modem
    Flashing greenNo connection to the Internet or
    the modem
    Flashing redStart-up mode, or error
  4. Connect a Ethernet cable from one of the four white Ethernet ports on the rear of the SBR-AC3200P to the Ethernet port of a laptop or desktop.  For wireless devices, establish to open wireless network list and connect to SURFboard-XXXX (see SSID number listed on the router label). 

    Right click on the image to save it to your computer.
     
  5. To test Internet connection launch a web browser, such as Internet Explorer, Firefox, or Safari.  Enter www.surfboard.com into the address box, and press the Enter key.  The ARRIS website should open. 

Feedback

 

Was this article helpful?


   

Your feedback is appreciated.

Characters Remaining: 255

 

Print
-->